Tools

Wheels Manufacturing open bore adapters are used to press sealed cartridge bearings into place. The adapters are machined with one step to correspond to the bearing OD, which fits in to the center of the sealed bearing and an outside diameter to accommodate the bearing's outer diameter. Size: [Bearing inner diameter] x [Bearing outer diameter] Note: If only one dimension is given, that is the outer diameter of the adapter, with no inner diameter step

Wheels Manufacturing Over Axle Adapters are used for pressing your most commonly used bearing sizes into place. Each represents an excellent addition to the Press-4 Bearing Press. - Adapters sold individually

- Sealed bearing extractor with 1/2-inch thru hole for use with Wheels Mfg. 1/2-inch threaded rod press handles - Part of a system that requires additional pieces to function

Receiver cup sleeve for Wheels Mfg. sealed bearing extractors. Machined aluminum sleeve, anodized red. - 1/2-inch thru hole to fit over their 1/2-inch threaded rod press handles - Part of a system that requires additional pieces to function

Wheels Manufacturing Sealed Bearing Extractor - 17mm Fits the following bearings: - 6003 - 6803 - 6903 - 17287

Frame linkage standoff works with Wheels Mfg. bearing press handles. Acts as a spacer to allow the press handles to fully seat bearings over suspension linkages that protrude beyond the face of the bearing. - OD: 15.8mm / ID: 9.9mm - Machined aluminum - Anodized red - Sold individually

Easy-to-use tool removes and installs replacement bushings in suspension and shock pivots. Includes retaining tool, top cap, and three sizes of bushing drifts. - Fits eyelet sizes - 10mm, 12mm, and 1/2" - Machined aluminum - Anodized Red

Wheels Manufacturing Sealed Bearing Extractor - 15mm Fits the following bearings: - 6002 - 6702 - 6802 - 6902 - 15267 - 15268

Wheels Manufacturing Sealed Bearing Extractor - 8mm Fits: - 608 - 688 - Other bearings with an inside diameter of 8mm

The Wheels Manufacturing universal bottom bracket drift presses all current Wheels Mfg bottom bracket cups into your frame or bearing cups. The adapter is machined with multiple steps to fit common bottom bracket shell and bearing diameters listed below. Each step is laser etched with the diameter size. - Inner hole sized to fit 1/2" threaded rod. Not for use with Wheels Mfg PRESS-1 or PRESS-4 - Compatible with any other press with a 1/2" diameter rod - Recommended for use with Wheels Mfg Universal BB Press - Machined aluminum - Anodized Red - Sold individually - Drift can also be used as a frame bottom bracket shell sizing guide! Fits the following bottom bracket shell sizes: - BB30 (42mm) - PF30 (46mm) - BB86, BB92 (41mm) - BBRight (46mm) - BB386EVO (46mm) - Cannondale BB30A (42mm) - Cannondale PF30A (46mm) - Specialized Carbon OSBB (46mm) - Specialized Alloy OSBB (42mm) - TREK BB90, BB95 (37mm) - PF24 (41mm)

Wheels Manufacturing Sealed Bearing Extractor - 30mm Fits: - 6806 - Other bearings with an inside diameter of 30mm

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body. - Anodized in Wheels MFG red.

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body - Anodized in Wheels MFG red.

- Essential bearing press for installation of bearings with a 10mm minimum ID - (1) 3/8 ACME threaded rod, (2) 30mm standoffs, (2) threaded handles

Precision-machined anodized aluminum designed to allow for easy adjustment of the Fox DHX2/FLOAT X2 shocks requiring a 3mm and 6mm hex wrench. This small, pocket-sized tool allows for easy trail-side adjustments.

- Allows for quick and accurate positioning at the press of a button - Slides along 1/2" UNC threaded press rod when the button is depressed and can be placed quickly to secure drifts, spacers, and cups when completing maintenance or installation of bike headsets, bottom brackets, and bearings

Shock Bushing Press Kit An evolution of our original bushing toolset which required the use of a hammer to pound out shock bushings. The new design uses our threaded handle press system to easily and efficiently remove shock bushing in 12mm and 1/2 inch sizes. - Fits 12mm and 1/2" bushings. - Machined aluminum - Anodized Red

Use this double-sided socket tool for installing and removing both 48.5mm and 44mm 16-notch bottom bracket cups. Socket is machined for 1/2-inch drive, but a 3/8-inch to 1/2-inch adapter is included so you can use it with 3/8-inch drive torque wrenches. - Compatible with all Wheels Manufacturing bottom brackets that have 48.5mm or 44mm, 16-notch spline patterns - Also compatible with FSA MegaEVO BB cups, Shimano, SRAM/Truvativ, Campagnolo Ultra Torque, and FSA - Machined 6061 aluminum - Anodized red

BB30 service kit for SRAM DUB cranks. - Includes (2) Enduro 6806/29 ABEC-3 sealed bearings and 2 retaining clips - Bearing Dimensions: OD: 42mm / ID: 29mm / Width: 7mm - Enduro ABEC-3 bearings - Use with SRAM DUB cranks Note: SRAM DUB cranksets are not designed to work in 68mm or 73mm wide shells with inboard bearings. Use only if your frame is a direct-fit bearing system, and the BB shell width is 86.5mm or wider.

- Machined to match manufacturer specifications and designed to be used with a ½” drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body. - Anodized in Wheels MFG red.

- Machined to match manufacturer specifications and designed to be used with a 1/2" drive socket or torque wrench for easy installation and removal of e-bike lockrings. - Precision machined aluminum body. - Anodized in Wheels MFG red.

Our 6806 open bore adapter is used to press 42x30 sealed bearings. The adapter is machined with one step at 30mm ID, which fits into the center of the sealed bearing. Common bearing size for BB30 frames and bottom brackets. - Installs: 6806 bearing - Inner step outer diameter: 29. 9mm - Outer diameter: 41. 8mm - Thickness: 7mm - Thru hole diameter: 0. 387" (9. 8mm) - Inner hole sized to fit 1/2" threaded rod - Compatible BP0006, BP0007 - Machined, red anodized aluminum - Sold individually (2 drifts required for some installations)

- Bottom bracket and bearing installation kit - (1) 1/2" rod, (2) threaded handles - (1) 2237 OPEN BORE, (2) 2437 OPEN BORE, (2) 29mm OPEN BORE, (2) 6806 OPEN BORE, (1) FRAME DRIFT

Wheels Manufacturing Sealed Bearing Extractor - 9.5mm Fits: - R6 (3/8-inch) bearings - Other bearings with an inside diameter of 9.5mm

Wheels Manufacturing Sealed Bearing Extractor - 9mm Fits: - 609 - 9227 - Other bearings with an inside diameter of 9mm

This 29mm open bore adapter is used to press 29mm x 42mm (DUB) sealed bearings. The adapter is machined with one step at 29mm OD, which fits into the center of the sealed bearing. For use with Wheels Mfg. bottom bracket press (PRESS-7 , PRESS-7-PRO or PRESS-9-PRO). - Inner step outer diameter: 28.9mm - Outer diameter: 41.8mm - Thru hole diameter: 12.8mm (1/2-inch) - Thickness: 7mm - Machined, red anodized aluminum - Sold individually

Precision-machined anodized aluminum tool designed to allow for easy installation, removal, or adjustments of the Shimano Hollowtech II Crankset compression bolt.

Wheels Manufacturing Sealed Bearing Extractor for GXP (22mm) bearings Fits: SRAM GPX bottom bracket bearings and other bearings with an inside diameter of 22mm

The dropout saver system is an alternative to replacing badly bent or damaged derailleur dropouts. Rather than replacing the damaged dropout completely, simply drill out the damaged threads, install a dropout saver, and realign the dropout. Kit includes: - (1) 15/32-inch reduced shank drill bit - (2) DS-1 wide dropout savers     - (3) DS-2 narrow dropout savers    

Wheels Manufacturing Sealed Bearing Extractor - 12mm Fits the following bearings: - 6001 - 6801 - 6901